Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Chico Homeowners
When a driveway gate stops opening, drags along its track, or an operator clicks and does nothing, you need someone who can read the equipment, not guess at it. Gate Repair Chico is a gate-only specialist. We handle mechanical failures and electric gate diagnosis on the same visit, and our technicians have up to 9 years of experience working across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems. That matters in Chico, where a mix of older iron estate gates and newer automated driveways means no two repairs look alike. We quote the price before any work starts, so the written estimate is what you pay. Same-day repair is often possible when you call early. Reach us at (866) 369-2364. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Driveway Gate Repair
Driveway Gate Repair covers the whole entry assembly at the mouth of your property, from the hinges and latch to the operator that moves the leaf. You need it when a gate sags, binds, stops halfway, or the arm struggles against a stiff hinge. In Chico’s hot, dry summers, wooden and painted steel gates swell and shrink with the seasons, and hinges that were fine in spring start to catch by August. We inspect the full travel of the gate, test the operator under load, and check the safety edges before we recommend anything. Typical driveway gate repair in Chico runs $150 to $600 depending on whether it’s a mechanical fix or an operator issue; the written estimate sets the final price.
Hinge, Latch, and Alignment Fixes
Sagging gates are the most common call we get. We reset hinges, re-hang a leaf that has dropped, and true up the latch so the gate closes square instead of rubbing. Left alone, a misaligned gate wears out the operator faster because the motor fights the drag on every cycle.
Operator and Arm Adjustments
When the gate moves but not smoothly, the problem is often in the operator’s limit settings or the drive arm. We adjust travel limits, re-torque the arm, and confirm the gate reverses on obstruction. This is where brand familiarity saves time: we know how Ghost Controls and Elite units respond to adjustment.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding is the structural repair work that keeps a metal gate from failing at the joints, and it’s what you need when a hinge plate tears loose, a post bracket cracks, or a frame rail splits at a weld. On Chico properties, gates built from tube steel and wrought iron take a beating from sun and dry air, and a weld that was marginal when new can fail after a few summers. We weld on-site where the gate allows it, or remove a leaf for bench work when the joint needs a full re-penetration. Structural gate welding in Chico typically runs $200 to $650 depending on the number of joints and whether the leaf has to come off. Every weld is inspected for penetration before we call the job done.
Hinge and Bracket Welds
A hinge that pulls out of the frame is a structural failure, not just a loose screw. We cut back to sound metal, re-weld the plate, and check the gate’s swing so the load is spread correctly. Poorly done hinge welds are why gates come back out of alignment.
Frame and Rail Repair
Cracked rails and split frame members get cleaned, prepped, and welded with a proper root pass. On heavier iron, we check the whole frame for stress before we finish, because one crack usually means the gate is working against itself somewhere else.
Commercial Gate Repair
Commercial Gate Repair handles the heavier slide and swing systems on business lots, storage facilities, and multi-unit properties, where a gate that won’t open is a real operational problem. You need it when a DoorKing or LiftMaster commercial operator faults out, when a slide gate jumps its track, or when access control stops releasing the gate for authorized vehicles. We diagnose the full chain: the operator, the loop and safety sensors, the control board, and the mechanical track. Commercial gate repair in Chico typically runs $250 to $900 depending on whether the fault is mechanical, electrical, or in the access control layer. We quote the price up front and stick to it.
Operator and Control Board Faults
Commercial operators log faults differently than residential units, and a board that won’t reset is rarely the board’s fault alone. We test the inputs first, including safety loops and photo eyes, before condemning a control board. That approach often saves the cost of a board that didn’t need replacing.
Track, Roller, and Guide Repairs
Heavy slide gates ride on rollers and guides that wear faster under constant commercial use. We measure the track for true, replace worn rollers, and check that the gate can’t lift off its guides. A gate that comes off the track is a serious safety issue, so we address it the same visit.
Iron Gate Repair
Iron Gate Repair is the fix for ornamental and structural iron gates that have lost their alignment, cracked at a casting, or stopped latching cleanly. It’s what you need when an iron gate drags, binds, or shows rust creeping along a joint, and it’s common on Chico properties with older iron entries that were installed before the operator was added. We check the hinge geometry, the post mounting, and the iron’s overall rigidity. Cast and wrought iron repairs are temperamental, so we test fit before final assembly. Iron gate repair in Chico typically runs $175 to $600 depending on whether it’s an alignment issue, a hinge repair, or a structural weld. The estimate is agreed before work begins.
Alignment and Swing Correction
Iron gates are unforgiving about alignment. We reset hinge geometry and adjust the post brackets so the gate swings without binding, which protects both the iron and the operator. A gate that swings true lasts longer than one forced closed every day.
Rust and Joint Treatment
Rust at a joint or weld is a structural warning, not a cosmetic one. We treat the affected area, remove loose scale, and protect the joint so the corrosion doesn’t keep eating the member from the inside. Severe rust cases are flagged before anything is welded over.
Sliding Gate Repair
Sliding Gate Repair is the service for gates that roll along a track instead of swinging, and you need it when the gate sticks, jumps the track, or the operator strains to move it. Sliding gates carry heavy loads, and small problems like a worn roller or a track that’s out of true turn into a gate that comes off its guides if you leave them. In Chico, concrete and track movement from the dry, shifting ground can throw a slide gate out of alignment over time. We inspect the track, rollers, guides, and operator together, since a strained motor is usually a symptom of a mechanical drag. Sliding gate repair in Chico typically runs $200 to $700 depending on the fault, with the written estimate setting the final price.
Roller and Track Replacement
Worn rollers and bent track are the two biggest causes of a dragging slide gate. We replace the rollers, level the track, and confirm the gate rides without lateral force. Getting the load off the operator is what keeps the motor from burning out.
Guide and Stop Adjustments
Guides that are out of adjustment let the gate wander and jam. We reset the guides and stops so the gate tracks true and hits its limit without slamming. A gate that can lift off its guides is a safety hazard, so we check that every visit.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on the decorative forged-iron entries that are common on older Chico properties, where the value is in the ornamentation as much as the function. It’s what you need when a scroll or casting cracks, a finial loosens, or the gate has lost its shape. Wrought iron is softer and more forgiving than cast iron but also more prone to deforming at the hinge, so we work carefully to preserve the original profile. We also check the mounting hardware, since a loose post bracket is often what started the problem. Wrought iron gate repair in Chico typically runs $175 to $550 depending on the ornamentation and weld work involved.
Ornamental Weld Repairs
Cracked scrolls and loose finials need low-heat welding so the surrounding iron doesn’t distort. We match the repair to the original style where we can. Anything that can’t be repaired cleanly is explained before we start, not after.
Post and Bracket Reinforcement
A wrought iron gate is only as solid as what holds it up. We reinforce loose post brackets and check whether the post footing itself is the problem. If a post is moving, the repair won’t hold until the footing is addressed.

Metal Gate Repair
Metal Gate Repair covers the widest range of gates on Chico properties, from tube-steel drive gates to aluminum pedestrian entries and everything welded or bolted together in between. You need it when the frame flexes, a bracket bends, or the gate has started to sag at the hinge after years of use. Metal ranges from light aluminum that cracks at a stress point to heavy steel that bends but holds, and each needs a different fix. We check the frame, brackets, hinges, and the operator under load before we recommend a repair or replacement. Metal gate repair in Chico typically runs $150 to $650 depending on the material and severity, with the final price set by the written estimate.
Bracket and Frame Straightening
Bent brackets and twisted frames are common on gates that get bumped or leaned on. We straighten the member and reinforce it so it carries the load again. A reinforced bracket that’s done right outlasts a straight replacement of the same weak part.
Hinge Replacement and Reinforcement
Hinges are where most metal gates fail. We replace worn hinges and add reinforcement plates at the mounting point so the steel doesn’t fatigue around the bolts. This is especially important on aluminum, which fatigues faster than steel at a hinge.
Wood Gate Repair
Wood Gate Repair is the fix for timber gates that have swollen, split, warped, or dropped on their hinges, and it’s common on Chico driveways where the wood takes the full summer heat. You need it when the gate sticks in the frame, a hinge has pulled out of soft wood, or planks have started to gap at the joints. Wood moves with the seasons here, and a gate that fit tight in winter can bind by mid-summer. We repair the frame, reinforce the hinges with proper plates, and address the joints before we touch the finish work. Wood gate repair in Chico typically runs $150 to $500 depending on the extent of the repair and how much of the gate has to be rebuilt. The estimate is agreed before anything is cut.
Hinge and Frame Reinforcement
Wood hinges pull out when the timber around them softens. We back the hinge with a plate or a stronger block so the fastener bites into solid material. Without that reinforcement, the same hinge will pull out again the next dry season.
Warp, Split, and Joint Repair
Warped planks and split joints are repaired by working with the wood’s grain, not against it. We brace warped sections and splice split joints back to full strength. Where a plank is too far gone to save, we explain why and let you decide.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the equipment that’s actually on your gate. On the residential side, we service Mighty Mule and Ghost Controls operators, and we know how those units wear: the arm bushings, the limit switches, and the battery backup that goes soft over time. For heavier residential and light-commercial systems, we service LiftMaster and Elite, and we’re familiar with how those units handle the loads a bigger Chico gate puts on them. If your gate runs on a commercial-grade DoorKing operator, we know the control board, safety loops, and access control layer that make those systems behave. We also service FAAC, BFT, Linear, and Viking units, and we approach each brand the same way: read the equipment, test the fault, fix what’s actually broken.
Because we work across nine manufacturers, we don’t push you toward one brand’s ecosystem when a repair will do. We also handle the mechanical side of the same gate, so you’re not chasing a welder after an electrician. If your gate needs a brand-agnostic look at the whole system, visit our Gate Repair Chico page for the full picture. Whether you have DoorKing, Mighty Mule, Elite, or any other make, we can help.
Signs You Need a Pro Right Now
- The gate moves but the operator strains or clicks. A motor that fights resistance is a sign the gate is dragging on a hinge or roller, and running it that way wears out the operator. Get it looked at before the motor gives out, not after.
- The gate jumps the track or lifts off its guides. On a slide gate, this is the most serious warning sign. A gate that can come off its track is a safety hazard to vehicles and people, and it needs an on-site check.
- The gate sags or drags on the ground. A sagging gate means the hinge or post has failed. Ignoring it puts the full load on the operator, which is where the real bill comes from.
- The safety edges or photo eyes stop responding. Safety devices that fail can let the gate close on an obstruction. This is an electric gate fault that needs diagnosis, not a reset button.
- A weld or hinge plate pulls away from the frame. Structural separation at a weld means the gate is failing at the joint. That’s a job for welding, and it gets worse fast if the gate keeps cycling.
Our Process, Step by Step
- 1
Listen and diagnose over the phone. We ask what the gate is doing, what brand the operator is, and how long it’s been happening. That short conversation tells us whether this is likely a mechanical or an electrical fault before anyone comes out.
- 2
On-site evaluation and testing. When we’re there, we test the gate through its full travel and check the operator under load. We use basic diagnostic tools to read the operator’s fault codes where the unit supports it, and we check the safety devices as part of the same visit.
- 3
A written estimate, agreed before work. Once we know what’s wrong, you get a written estimate before anyone picks up a tool. No work begins until you approve the price. That’s the whole point of the estimate.
- 4
The repair itself. Mechanical work like hinge resets and welding happens alongside the electrical diagnosis on the same visit where possible. If a part has to be sourced, we tell you when it’s expected and why we chose that part.
- 5
Test and walk-through. We cycle the gate, test the safety edges, and show you what was fixed. If the gate needs follow-up mechanical repair before the operator work is complete, you’ll know before we leave.
How Much Does Gate Repair Cost in Chico?
Gate repair in Chico typically costs $150 to $900, depending on whether the problem is mechanical, electrical, or structural. A typical driveway gate repair runs $150 to $600. A typical iron or wrought iron repair runs $175 to $600. A typical sliding gate repair runs $200 to $700. Commercial gate repair on a DoorKing or LiftMaster system runs $250 to $900. Wood gate repair runs $150 to $500, and gate welding runs $200 to $650.
What moves the price: whether the gate has to come off its hinges for bench work, whether a control board or operator part has to be replaced, and how much welding is involved. Brand also matters: a standard residential operator part is usually cheaper than a commercial DoorKing board. You avoid overpaying by getting a written estimate before work starts, which is exactly what our free estimate gives you. That estimate covers the diagnosis, the likely repair, and the part cost where we can confirm it. Anything we can’t confirm until we’re on-site, we say so up front rather than padding the number. The final price is set by the written estimate you approve, so an invoice bigger than the quote isn’t a scenario here. Call (866) 369-2364 for an exact quote.
Our Service Area Near Chico
We cover Chico and the surrounding communities, including Durham to the south and Kelly Ridge and Oroville to the southeast, plus Paradise, Magalia, Orland, Thermalito, Corning, and South Oroville. Typical response is same-day or next-day depending on where you are and when you call; the further out towns can take a little longer. If you’re in Durham, see our gate repair page for local details. If you’re in Kelly Ridge, our gate repair page has your area covered.
Serving Chico, CA – Our Local Coverage Area
We serve Chico and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Chico
Gate repair is the diagnosis and fix of a malfunctioning gate, covering the mechanical assembly (hinges, latches, tracks, rollers, frame, welds) and the electrical side (operator, control board, safety edges, access control). Gate Repair Chico does both on the same visit where possible, so you’re not shuttling between a welder and an electrician. We work on nine brands including DoorKing, Mighty Mule, Elite, and Ghost Controls. Call (866) 369-2364 for a free estimate.
Most mechanical repairs are finished within a few hours. A hinge reset or simple weld can be done in under two hours; an operator fault or a control board diagnosis takes longer, and a part that has to be sourced adds days, not weeks. Welding jobs on a heavy commercial gate can run most of a visit. We give you a realistic time window when we call, not when we arrive.
A typical repair in Chico runs $150 to $900 depending on the service: driveway gate repair is $150 to $600, sliding gate repair is $200 to $700, commercial gate repair is $250 to $900, and welding is $200 to $650. Prices are estimates set by the written quote you approve before work starts. Call (866) 369-2364 for an exact quote, free of charge.
Yes. We service DoorKing, Mighty Mule, and Elite operators, along with LiftMaster, FAAC, BFT, Linear, Viking, and Ghost Controls. We’re independent and not tied to any one manufacturer, which means we diagnose the actual fault rather than steering you toward a replacement system. Call (866) 369-2364 to book a diagnostic.
Same-day repair is often possible if you call early in the day. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (866) 369-2364 to check today’s availability.
We stand behind the work we do and will discuss warranty terms on the written estimate before any work begins. Parts carry their own manufacturer coverage, and we explain what that covers when we quote. If something we repaired isn’t right, call us. Call (866) 369-2364 with questions about coverage.
Clear the gate’s path of vehicles and obstructions, unlock any manual release, and make a note of the operator brand and model if you can see it on the unit. If the gate failed after a power event, mention that to us; it changes how we diagnose the operator. None of this is required, but it saves time on the visit. Call (866) 369-2364 to schedule.
Schedule Your Gate Repair Service in Chico Today
We’re gate-only specialists, which means the technician who shows up works on gates every day, not garages, fences, or general handyman calls. Whether it’s a Mighty Mule on a driveway or a DoorKing on a commercial lot, we diagnose the actual fault and give you an upfront price before any work starts. Call (866) 369-2364 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Chico.