Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Orland
If your gate has stopped opening, is dragging on the ground, or the operator runs but nothing moves, we’re the gate-only team Orland calls. Gate Repair Chico works on mechanical and electric gate systems across Orland and the surrounding orchard country, and we know the brands on your operator by name. Most Orland gate calls come down to power and span: a long driveway, a wide farm gate, a solar panel that can’t keep up, or a post that’s given out below the ground line. We figure out which one it is before we quote anything. Call (866) 369-2364 for a free estimate. Our technicians have up to 9 years of experience.
Why Orland Homeowners Call Gate Repair Chico for Gate Repair
Orland gate work isn’t the same as suburban gate work, and that’s the reason people here call us. Out on the rural parcels, a driveway gate might span twenty feet and run on a solar operator because mains power never made it that far. In town, it’s older homes with side-yard gates and detached garages where the hinge hardware has been through decades of hot summers and wet winters. We service both ends of that, from a Mighty Mule on a residential driveway to a DoorKing on a commercial lot, and we diagnose the specific brand on your gate instead of guessing.
We’re gate-only specialists. That focus matters when a gate sags, sticks, or quits under load, because the fix is usually in a place a general handyman doesn’t think to look, like the buried post rather than the panel or the operator. Our reputation around Orland is built on that kind of diagnosis and on honest repair calls when a system doesn’t need replacing. Call (866) 369-2364 and we’ll get an estimate scheduled.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Iron Gate Repair in Orland
Iron Gate Repair in Orland means dealing with rust, seized hinges, and posts that have moved, and it’s a big share of what we see on the rural properties around the valley floor. Wrought and steel gates here take a beating from irrigation overspray and gravel dust, and the hardware rusts faster than the gate face does. We handle hinge and post repair, realignment, lock repair, and weld and rust repair. A typical iron gate repair in Orland runs $150 to $450, and post replacement on a long driveway entrance can run higher, so we quote it after we’ve checked the footing.
Hinge and Post Repair
On a heavy iron gate, the hinge often carries the blame for a problem that starts lower down. When a post has rotted at the ground line, the whole gate leans and the hinges bind. We check the post first and set a new one in concrete when that’s the real cause.
Weld and Rust Repair
Rust at a weld joint is a structural issue, not a cosmetic one. We clean out the failed weld, repair the joint, and treat the steel so it holds up through another wet season. Ignoring it usually leads to a cracked frame.
Sliding Gate Repair in Orland
Sliding Gate Repair in Orland most often comes down to a wide farm gate that’s dragging, jumping the track, or moving unevenly under tractor traffic and gravel dust. Rack and pinion wear shows up as a gate that lurches or stalls partway through travel, and the same grit that wears the rack can foul the loop detector or photocell. A typical sliding gate repair in Orland runs $200 to $600, and operator and control work is quoted after we’ve tested the whole system. We check alignment, the track, and the operator together before we recommend anything.
Rack and Pinion Wear
Wide gates on gravel drives wear the rack and pinion faster than a short suburban gate ever will. When the teeth wear unevenly, travel gets rough and the operator works harder. Replacing the worn section restores smooth travel.
Loop Detector and Safety Faults
Dust and moisture get into loop detectors and photocells on rural drives, and a faulty safety edge or detector will stop an automatic gate from running safely. We test and repair that entrapment protection as part of the job.
Trusted Brands We Service in Orland
We work on the brand that’s actually on your gate. That includes Ghost Controls and Mighty Mule on residential driveways, DoorKing and Elite on heavier and light-commercial systems, and the other major operators in between. A gate repair team that knows one manufacturer’s ecosystem tends to push a replacement when a repair will do. We’re brand-agnostic, so the diagnosis drives the recommendation, not the parts we’d rather sell. We keep the turnaround fast by identifying the fault precisely before we arrive with a plan, and we tell you plainly whether the operator, the power, or the post is the problem. Call (866) 369-2364 to get your brand looked at.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Orland Homes
- Hinge post rot at the ground line. Tule fog and irrigation overspray keep valley posts damp long enough to rot below grade. The gate sags and the operator misaligns, and the real fix is the post, not the panel.
- Solar opener power loss on hot afternoons. Panels shaded by orchard trees or dust-covered from gravel drives can’t keep the battery charged through intense summer sun. We test the panel, battery, and charge controller.
- Rack and pinion wear on wide slide gates. Tractor traffic and gravel grit wear the rack unevenly, so the gate travels rough or stalls. It also fouls loop detectors on the same drive.
- Swollen and warped gates in town. Older Orland homes have wood and iron side-yard gates that dry, warp, and stick with the season. Realignment and hardware repair usually get them working again.
Pricing for Gate Repair in Orland, CA
Gate repair in Orland is priced per job, and the written estimate sets the final price before any work starts. Typical ranges: hinge and hardware repair runs $150 to $350, iron gate realignment and weld repair runs $200 to $450, and sliding gate repair with rack, track, or safety-component work runs $200 to $600. Post replacement on a rural driveway entrance can run $400 to $900 depending on the footing and the gate’s weight. Solar operator and control-board diagnosis and repair is quoted after we test the system, since the cause varies from panel to battery to controller. The estimate is free, and you’ll know the number before we pick up a tool. Call (866) 369-2364 for yours.
We Also Serve Cities Near Orland
We take gate repair calls across the northern valley, including Corning, Chico, Durham, and Paradise. If your gate is on a rural driveway outside Orland city limits, we can still get it looked at. Our gate repair team handles the full range, from a sagging farm gate to a failed control board. Call (866) 369-2364 to schedule in any of these towns.
Serving Orland, CA – Our Local Coverage Area
We serve Orland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Orland
It usually sags because the hinge post has rotted below the ground line, not because the gate frame failed. Tule fog and irrigation overspray keep valley posts damp long enough to rot where you can’t see it. A qualified technician digs out the old footing, sets a new post in concrete, and then corrects the sag on the panel. Call (866) 369-2364 for a free estimate.
Yes, a solar opener can work well on a long driveway when the panel gets real sun and the battery and controller are sized right. The failures we see come from orchard-tree shade and dust on the panel, which starve the charge. We test the panel, battery, and charge controller and repair what’s actually failing. Call (866) 369-2364 to schedule a diagnosis.
When the operator runs but the gate barely moves, the usual cause is worn rack and pinion, a bound wheel, or debris in the track. Gravel dust and tractor traffic on a wide farm gate wear these parts faster than a short gate would. We check alignment, the rack, and the operator together. Call (866) 369-2364 for an exact quote.
Automatic gates need working entrapment protection, which means functioning photocells and, where the gate travels, a safety edge or loop detector. A gate that runs without working safety devices should not be operated. We test and repair that protection as part of the job. Call (866) 369-2364 for a free estimate.
Check the hinge post at the ground line first, then the hinges and latch. Winter tule fog keeps posts damp, and a rotted base throws the whole gate out of line so it binds. A technician confirms the post before blaming the gate. Call (866) 369-2364 to get it looked at.
If your gate is dragging, stuck, or the operator’s quit, give us a call. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and the estimate is free. Call (866) 369-2364 to get your Orland gate working again.
Written by the team at Gate Repair Chico.