Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Chico?
Gate parts and welding in Chico typically run $150 to $1,900. A small repair, like replacing a bent hinge or welding a cracked latch, usually lands between $150 and $350, while a full section rebuild or gate re-hanging with new posts and hardware can reach $900 to $1,900. Parts cost is the biggest swing: a control board for a DoorKing or LiftMaster operator can cost several times what a Mighty Mule battery or Ghost Controls arm runs.
We price every job per job from a written estimate, and the estimate is free. Call (866) 369-2364. We answer 24/7, and we book fast dispatch from 7am to 7pm, Sunday through Friday.
Gate Parts & Welding Cost Breakdown (2026)
Below are typical Chico-area ranges for common parts and welding work on residential and light-commercial gates. The written estimate sets the final price; these are estimates, not quotes.
| Work Item | Typical Range (Chico, 2026) |
|---|---|
| Hinge replacement (per hinge, parts + labor) | $75 – $180 |
| Latch or catch repair | $90 – $220 |
| Weld repair on frame, post, or bracket | $150 – $450 |
| Rust removal and touch-up weld on lower frame | $180 – $400 |
| Slide gate roller and track replacement | $220 – $550 |
| Gate re-hang or sag correction | $250 – $650 |
| Automated operator arm or motor replacement (Ghost Controls, Mighty Mule, Viking) | $320 – $750 |
| Control board or receiver replacement (LiftMaster, Linear, FAAC, BFT) | $280 – $700 |
| Photo eye / safety sensor pair | $180 – $380 |
| Keypad or access control component | $200 – $550 |
| DoorKing light-commercial operator service | $350 – $900 |
| Full frame rebuild (small residential gate) | $900 – $1,900 |
What drives the number up or down: the brand and availability of the part, whether the gate is residential or light-commercial, how much of the old metal has to be cut out before new steel goes in, and whether an operator needs to be removed and remounted to get at the weld. A broken hinge on a Mighty Mule swing gate is a one-visit job. A bent post on a slide gate running a DoorKing operator takes longer, because the track and the operator both have to come back into alignment after the weld. Brand-specific parts are the other factor; we work with nine manufacturers, so we’re not guessing which control board fits your FAAC or which arm matches your Elite.
What Affects Gate Parts & Welding Pricing in Chico
- Which brand is on the gate. Parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule vary widely. A Mighty Mule battery is a different line item than a DoorKing control board. Knowing the exact model on the operator keeps the estimate tight.
- Gate material and weight. Light steel tube welds fast. Heavy wrought iron or a solid metal panel takes more prep, more rod, and more time to line back up.
- Rust and sun. Chico summers are dry and hot, and gates here rust at the bottom rail where irrigation spray and sprinkler overshoot sit on the steel. Rust that has eaten through the frame means cutting out metal before welding, which adds cost.
- Weld location on the frame. A hinge weld at the post is simple. A cracked weld hidden inside the gate frame, behind paneling or below the ground line, means disassembly and digging, so it costs more.
- Whether it’s an automated system. Electric gates add operator wiring and safety sensor work on top of the mechanical repair. Access control components like keypads and receivers also add to the ticket.
- Residential vs. light-commercial. Commercial-grade slides and swings use heavier hardware and take longer, and the parts are priced higher.
If you’re weighing a repair against a bigger project, our team at Gate Repair Chico walks through part availability and timeline before anyone quotes. It’s the difference between patching a hinge and replacing a whole gate section, and we tell you plainly which one the gate actually needs.
How to Save on Gate Parts & Welding
Get the estimate before approving anything. A free written estimate lets you see the parts line and the labor line separately, so you’re not guessing at a flat number over the phone.
- Fix small welds early. A hairline crack at a hinge bracket costs $150 to $250 to weld now. Wait until the bracket tears out of the frame and the repair jumps toward $450 or more.
- Keep the bottom rail dry. Reset sprinklers that spray the gate, and keep the bottom rail painted. Rust removal adds real cost when it turns into metal replacement.
- Know your model number. If the operator’s tag is legible, the part is easy to source. If the tag is gone, we identify the unit by shape, arm, and control box, but a legible tag saves time.
- Repair before replace where the gate is sound. A control board replacement for a LiftMaster or Linear operator usually costs less than a new operator, and much less than a new automated gate. We diagnose brand-agnostic, so there’s no push to swap a working system.
- Bundle small items into one visit. If the latch needs welding and a photo eye is failing, handle both in the same appointment and the labor folds together.
Call (866) 369-2364 for a free estimate. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician to look at the gate and write the number down.
FAQs – Gate Parts & Welding Cost in Chico
How much does gate welding cost in Chico?
Most gate weld repairs in Chico run $150 to $450. A short weld on a hinge, latch, or bracket sits near the low end, while a cracked frame or a bent post on a slide gate trends higher because the gate has to be re-aligned afterward. Call (866) 369-2364 for an exact quote, and estimates are free.
Is it cheaper to repair or replace a gate in Chico?
Repair is usually cheaper when the gate frame and posts are sound. A weld and hinge repair in the $150 to $450 range versus a full frame rebuild at $900 to $1,900 is a wide gap, so repair wins unless the metal has rusted through at the base or the post footing is compromised. We’ll tell you which side of that line your gate is on, and we don’t push a replacement when a repair does the job.
How much does a gate opener part cost in Chico?
Expect $180 to $750 for most operator parts, depending on the brand and component. A safety photo eye pair runs $180 to $380, a control board for a LiftMaster, Linear, FAAC, or BFT operator runs $280 to $700, and an arm or motor on a Ghost Controls, Mighty Mule, or Viking swing gate runs $320 to $750. Call for the exact part on your model.
Can you come today for a gate parts or welding issue?
Yes, same-day service is often possible. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician out to diagnose the gate. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. If a gate has fallen off its track or a heavy panel is hanging, keep people and vehicles clear of it until a technician arrives; a moving gate panel can crush a hand or foot.
Do you work on all gate brands in Chico?
We service nine named brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That spans basic residential DIY-grade systems up to light-commercial doors. Our technicians have up to 9 years of experience, and we work on the mechanical repair, the electric and automated side, and full installation, so you don’t need a separate contractor as the gate ages. If you’re in Chico and want a straight diagnosis, call (866) 369-2364.
Why We Focus on Parts, Welding, and the Brand on Your Gate
Gate work is a specific trade. The parts are specific, the welding is specific, and the operators are specific. We stay on gates only, which means we’re reading a LiftMaster control board one visit and a DoorKing operator the next, and we know the difference in the field. It also means we’re not the general handyman down the road who happens to own a welder. From worn hinges to failed control boards, that focus is what keeps the estimate honest and the repair right the first time. If you’re ready to get a number, our Chico team can help.
Get a Free Gate Parts & Welding Estimate in Chico
A gate repair is a lot easier to plan once you have a number. Call (866) 369-2364 for a free estimate. We answer 24/7, and fast dispatch from 7am to 7pm, Sunday through Friday, gets a technician out to look at the weld, the hardware, or the operator and tell you what it costs. Licensed and insured, with upfront pricing on every job, and no pressure to replace what can be fixed. Whether it’s a Mighty Mule on a driveway or a DoorKing on a commercial lot, call and let’s get it sorted.
Pricing reflects the Chico market as of 2026. Gate Repair Chico offers free estimates. Call (866) 369-2364.
Written by the team at Gate Repair Chico.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Maria Delgado"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Todd Hoffman"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Carlos Mendoza